FLY'N THINGS(tm) PCX-To-DXF Conversion Version 1.0  4/2/95

README.TXT - The file you are reading

INSTALLATION:

Operating features of the PCX-To-DXF Conversion program REQUIRE that
it be run under Windows 3.1 or later in the enhanced mode.

The PCX-To-DXF program works best with Super VGA running at 800 x 600
resolution. However, it HAS been tested with Windows running standard
VGA at 640 x 480 resolution. This is a Visual Basic program and requires
VBRUN200.DLL to be installed in the WINDOWS or WINDOWS/SYSTEM directory. 

1.  IF YOU DO NOT HAVE A COPY OF VBRUN200.DLL ON YOUR SYTEM:

  a.  If you have a disk copy, copy VBRUN200.DLL from the disk
      to your WINDOWS or WINDOWS\SYSTEM directory.

  b.  If you have downloaded the PCXTODXF.ZIP file from an on-line service,
      download a copy of VBRUN200.DLL, too. Usually it's stored as
      VBRUN200.ZIP. 

2.  From Disk:

PCX-To-DXF conversion uses a standard Windows installation program. The
program comes on a single high-density (1.44Mbyte) 3-1/2 inch disk.
Place the disk in your 3-/12-in. drive. From the Windows Program
Manager File Menu, select RUN... Type A:\SETUP and press the Enter
key. The automatic install program prompts you for any changes, like
hard drive or directory. When complete, the install program creates
a new File-Manager Group containing the PCX-To-DXF Icons. A special
PCX-format file: RYANTEST.PCX is included so you can test the output
with a large-size file -- the non-registered version, while full
featured, is limited to PCX images no larger than 3-1/2 x 3-1/2 inches.

If you are new to Windows, select the program's Help menu and then
select How To Use Help for basic operation of Windows programs.
For information on the PCX-To-DXF conversion, select Contents from
the Help pull-down menu. Or, simply press function-key F1. 

3.  From A ZIPped Download:

Copy PCXTODXF.ZIP into a temporary directory on your hard drive. UNZIP the
file with an UNZIPping program. Copy the UNZIPped programs to a 1.44 Mbyte
floppy disk. Then, follow the above "From Disk" installation instructions.

OR:
To install directly from your hard drive, UNZIP the program to a 
temporary directory. Follow the "From Disk" installation procedure above,
but run SETUP from that directory on your hard drive. When the installation
is complete, delete all of the PCX-To-DXF installation files from the
temporary hard-disk directory.(Your may wish to save this file to your
installed directory for future reference)

PROGRAM FILES:

Normally Installed In Default Directory:  PCXTODXF

PCXTODXF.EXE	The Main PCX-To-DXF Program
PCXDXF.HLP	The Main PCX-To-DXF Help File
HELPHLP.HLP	How to Use Help
CMDIALOG.VBX	Part Of the PCX-To-DXF Program
FTEBK1.DLL      Part of the PCX-To-DXF Program
RYANTEST.PCX    Large-Format PCX Test Image
DXFHDR.TXT      DXF Header File For The Program

Installed In WINDOWS and/or WINDOWS/SYSTEM Directories:

PCXTODXF.INI	Part Of the PCX-To-DXF Program
VBCTL3D.VBX	Part Of the PCX-To-DXF Program

Also used by the PCX-To-DXF program is: CMDIALOG.DLL
that is part of Windows Versions 3.1 and 3.11

TO REMOVE The PCX-To-DXF Program From Your System:

Delete the directory with the PCX-To-DXF files (default: PCXTODXF)
and ALL files it contains (see File Listing above).

In the WINDOWS and/or WINDOWS/SYSTEM directories, delete the following
files ONLY if they are not needed by other Visual Basic Programs:

PCXTODXF.INI
VBCTL3D.VBX   (Used by all FLY'N THINGS(tm) Programs)

From the File Manager, delete the PCX-To-DXF program & Help Icons and
then delete the PCX-To-DXF Group. See your Windows manual
for detailed instructions.

**************************************************************** 
Copyright Notice

The FLY'N THINGS(tm) PCX-To-DXF Conversion Program is Shareware.
It is not FREE, nor is it is Public Domain. You should not have to
pay for this Shareware trail program other than the cost of download time
from an on-line service, or a disk-copy fee (not to exceed $3.00)
from a supplier of Shareware disks. On-line services MAY NOT ADD
A SURCHARGE TO DOWNLOAD THIS PROGRAM!

Please see the Warranty section of the main Help file. For a full
operating version of the program it must be registered. Please see
the Order and Registration section of the Help file for cost and
ordering information. Registration may be done by E-Mail or with
disk copies by mail.

Enjoy; your comments would be appreciated :-)

Phil Koopman, Sr.
2805 Hunt Club Lane
Orlando, FL 32826-3909
(407) 381-9464

AOL Member:  PKAeronaut

INTERNET:   PKAeronaut@aol.com
2805 Hunt Club Lane
Orlando, FL 32826-3909 U.S.A.
(407) 381-9464